JT- 34
THE
MODELS CONSTRUCTION
Frame.
Begin
the build of the model from gluing on 1 mm cardboard elements 1a, 1b, 1c, 2a, 3,
4a, 5a. From elements 1 to 5 glue the frames tub as showed in drawing 1 and 2.
Take caution while gluing together the elements, which shows the scheme in
drawing 2. Next you have to choose the version of the model: with the inside of
without it.
The
inside.
The
build of the inside begin from gluing both axles of the rocking levers A1, A2,
B1 as shown in drawing 3. When you make the movable rocking levers, you must fix
a rocking levers axle to the inside as in drawing S2. To the first pair of the
casing fix an axle as showed in drawing S1. Next glue the springs casing A3, A4,
A5 and B2.
If
you want to make a shock absorbered chassis, glue into the inside wires, so when
the lift becomes, the wheels are slightly bended. It is complicated
and usually only professional modeler can make it. It would be good, at
this level, to make the wheels rocking levers-elements 15 and 16 as well as the
driving wheels body transmission 17 and the mechanism tightening the caterpillar
18.
Next
glue elements A6 and then the fire-wall-A7 (in it you can cut out holes and glue
covers A8, A9, A10). Elements of the crews compartments equipment make as in
drawing 4. Next make the engine compartment as in drawing 5 from elements
B3-B10. From elements B11-B14 make the inside of the fuel tank(drawing 6) ,
which you glue between elements B2 and on element B10. Elements B15 glue as in
drawing 7 and glue it into the engines chamber beside the tanks B-11 and B-12
onto pieces B10a and B10b.
The
engine and the propulsion transfermake from elements marked by letter C. Glue
the engine from pieces C1-C14 as showed in drawing 8. The propulsion transfer,
pieces C15-C20 and B16 make as in drawing 9 and the filter configurationC21 and
C22 as showed in drawing 10.
Frame
cd.
Next you
glue pieces 6, 7, 8, 9, 10, 11, 12, 13 as showed in drawing 18, and then fix
wings 14.
Chassis.
The
build of the driving configuration begin from making the wheels rocking lever:
from pieces 15 make the front rocking lever, from piece 16 the remaining rocking
levers as showed in drawing 11. If you make movable rocking levers and circling
wheels glue also pattern S1, S2, S4. Elements 16j, 16k, 16l glue to piece 2 in
the marked spaces beside the holes for the springs. From elements 17 make the
transmission casing as showed in drawing 12 and glue it to the backj part of
element 2. The tightening mechanism- make pieces 18 as showed in drawing 13, but
pieces from d-i are not supposed to be glued at this level. Glue the capacity
wheels from pieces 19 as showed in drawing 14, the propulsion wheels from pieces
20 as showed in drawing 15, the tightening wheels from pieces 21 as showed in
drawing 16. If you make movable driving configuration you must take a good look
at the coaxial elements and the accuracy in gluing the wheels.Next make the
caterpillar from elements G1-G7 as showed in drawing 17. Next you complete the
frames equipment with the remaining elements as showed in drawing 18 and 19.
Tower
The
build of the tower begin from elements 32-35 as showed in drawing 20. Pay
attention while making elements 32-matching them to the holes in piece 6.
Elements 36e1 glue after fixing the outrigger. Make the outrigger as showed in
drawing 21 from elements 36, next join axles S11 to the tower. Make the
servo-motor from pieces 37 as showed in drawing 21, in the way, so that piece
37b would move inside of piece 37. Make the outriggers configuration from pieces
38 and 39 as well as pattern S12 and S13 as showed in drawing 22.
From
elements 40 and pattern S14 make the outriggers support construction, which you
glue to the frame using drawing 24.
In the
end the model can be painted with colourless and matt varnish.
WE WISH
GOOD LUCK ON CONSRUCTING THE MODEL!!